[Free] 2017(Oct) Dumps4cert Testinsides Cisco 200-125 Dumps with VCE and PDF Download 431-440

Dumps4Cert 2017 Oct Cisco Official New Released 200-125
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/200-125.html

CCNA Cisco Certified Network Associate CCNA (v3.0)

Question No: 431 – (Topic 8)

Which two Cisco IOS commands, used in troubleshooting, can enable debug output to a remote location? (Choose two)

  1. no logging console

  2. logging host ip-address

  3. terminal monitor

  4. show logging | redirect flashioutput.txt

  5. snmp-server enable traps syslog

Answer: B,C

Question No: 432 – (Topic 8)

In which byte of an IP packet can traffic be marked ?

  1. the Tos byte

  2. the Qos byte

  3. the Cos byte

  4. the Dscp byte

Answer: A

Reference: http://flylib.com/books/2/686/1/html/2/images/1587051990/graphics/13fig01.gif

Question No: 433 – (Topic 8)

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Why has the Branch3 router lost connectivity with R1?

Use only show commands to troubleshoot because usage of the debug command is restricted on the Branch3 and R1 routers.

  1. A PPP chap hostname mismatch is noticed between Branch3 and R1.

  2. A PPP chap password mismatch is noticed between Branch3 and R1.

  3. PPP encapsulation is not configured on Branch3.

  4. The PPP chap hostname and PPP chap password commands are missing on the Branch3 router.

Answer: A

Question No: 434 – (Topic 8)

Which statement about EIGRP on IPv6 device is true?

  1. It is configured directly on the interface

  2. the configuration uses secondary ip address

  3. the neighbors of each deice are directly configured

  4. the configuration uses process numbers

Answer: A

Explanation: Explanation/Reference: http://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol- eigrp/113267-eigrp-ipv6-00.html

Question No: 435 – (Topic 8)

Refer to the exhibit,

Dumps4Cert 2017 PDF and VCE

which command do you enter so that R1 advertises the loopback0 interface to the BGP peers?

A. network 172.16.1.32 mask 255.255.255.224

B. network 172.16.1.0 0.0.0.0.255

C. network 172.16.1.32 255.255.255.224

D. network 172.16.1.33 mask 255.255.255.224

E. network 172.16.1.32 mask 0.0.0.31

F. network 172.16.1.32 0.0.0.31

Answer: A

Question No: 436 – (Topic 8)

Which protocol advertises a virtual IP address to facilitate transparent failover of a Cisco routing device?

  1. FHRP

  2. DHCP

  3. RSMLT

  4. ESRP

Answer: A

Question No: 437 – (Topic 8)

Which spanning-tree feature places a port immediately into a forwarding stated?

  1. BPDU guard

  2. PortFast

  3. loop guard

  4. UDLD

  5. Uplink Fast

Answer: B Explanation:

PortFast causes a switch or trunk port to enter the spanning tree forwarding state immediately, bypassing the listening and learning states. You can use PortFast on switch

or trunk ports that are connected to a single workstation, switch, or server to allow those devices to connect to the network immediately, instead of waiting for the port to transition from the listening and learning states to the forwarding state.

Question No: 438 – (Topic 8)

Which mode is compatible with Trunk, Access, and desirable ports?

  1. Trunk Ports

  2. Access Ports

  3. Dynamic Auto

  4. Dynamic Desirable

Answer: C

Explanation: Explanation/Reference:

The #39;dynamic auto#39; will configure the port to accept incoming negotiation and will accept becoming either a trunk or an access port. Dynamic Auto allows the port to negotiate DTP (Dynamic Trunking Protocol) if the other side is set to trunk or desirable. Otherwise it will become an access port.

Question No: 439 – (Topic 8)

What are three characteristics of the TCP protocol? (Choose three.)

  1. It uses a single SYN-ACK message to establish a connection.

  2. The connection is established before data is transmitted.

  3. It ensures that all data is transmitted and received by the remote device.

  4. It supports significantly higher transmission speeds than UDP.

  5. It requires applications to determine when data packets must be retransmitted.

  6. It uses separate SYN and ACK messages to establish a connection.

Answer: B,C,F

Question No: 440 – (Topic 8)

What is the default VLAN on an access port?

  1. 0

  2. 1

  3. 10

D. 1024

Answer: B

100% Free Download!
Download Free Demo:200-125 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 200-125 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE