[Free] 2017(Oct) Dumps4cert Testinsides Cisco 200-120 Dumps with VCE and PDF Download 81-90

Dumps4Cert 2017 Oct Cisco Official New Released 200-120
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/200-120.html

CCNA Cisco Certified Network Associate CCNA

Question No: 81 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

What set of commands was configured on interface Fa0/3 to produce the given output?

  1. interface FastEthernet 0/3 channel-group 1 mode desirable switchport trunk encapsulation dot1q switchport mode trunk

  2. interface FastEthernet 0/3 channel-group 2 mode passive switchport trunk encapsulation dot1q switchport mode trunk

  3. interface FastEthernet 0/3 channel-group 2 mode active switchport trunk encapsulation dot1q switchport mode trunk

  4. interface FastEthernet 0/3 channel-group 2 mode on

switchport trunk encapsulation dot1q switchport mode trunk

Answer: B

Question No: 82 – (Topic 2)

Based on the network shown in the graphic

Dumps4Cert 2017 PDF and VCE

Which option contains both the potential networking problem and the protocol or setting that should be used to prevent the problem?

  1. routing loops, hold down timers

  2. switching loops, split horizon

  3. routing loops, split horizon

  4. switching loops, VTP

  5. routing loops, STP

  6. switching loops, STP

Answer: F

Question No: 83 – (Topic 2)

Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified.

What will happen in this scenario?

  1. 802.1Q giants frames could saturate the link.

  2. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.

  3. A native VLAN mismatch error message will appear.

  4. VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.

Answer: C

Question No: 84 – (Topic 2)

Assuming the default switch configuration, which VLAN range can be added, modified, and removed on a Cisco switch?

  1. 1 through 1001

  2. 2 through 1001

  3. 1 through 1002

  4. 2 through 1005

Answer: B

Question No: 85 – (Topic 2)

Refer to the topology shown in the exhibit.

Dumps4Cert 2017 PDF and VCE

Which ports will be STP designated ports if all the links are operating at the same bandwidth? (Choose three.)

  1. Switch A – Fa0/0

  2. Switch A – Fa0/1

  3. Switch B – Fa0/0

  4. Switch B – Fa0/1

  5. Switch C – Fa0/0

  6. Switch C – Fa0/1

Answer: B,C,D

Question No: 86 – (Topic 2)

Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.)

A. 802.1d

B. VTP

C. 802.1q

  1. STP

  2. SAP

Answer: A,D

Question No: 87 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

A network technician is asked to design a small network with redundancy. The exhibit

represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?

  1. This design will function as intended.

  2. Spanning-tree will need to be used.

  3. The router will not accept the addressing scheme.

  4. The connection between switches should be a trunk.

  5. The router interfaces must be encapsulated with the 802.1Q protocol.

Answer: C

Topic 3, IP addressing (IPv4 / IPv6)

Question No: 88 – (Topic 3)

What are three approaches that are used when migrating from an IPv4 addressing scheme to an IPv6 scheme. (Choose three.)

  1. enable dual-stack routing

  2. configure IPv6 directly

  3. configure IPv4 tunnels between IPv6 islands

  4. use proxying and translation to translate IPv6 packets into IPv4 packets

  5. statically map IPv4 addresses to IPv6 addresses

  6. use DHCPv6 to map IPv4 addresses to IPv6 addresses

Answer: A,C,D

Question No: 89 – (Topic 3)

What is the alternative notation for the IPv6 address B514:82C3:0000:0000:0029:EC7A:0000:EC72?

A. B514 : 82C3 : 0029 : EC7A : EC72

B. B514 : 82C3 :: 0029 : EC7A : EC72

C. B514 : 82C3 : 0029 :: EC7A : 0000 : EC72

D. B514 : 82C3 :: 0029 : EC7A : 0 : EC72

Answer: D

Question No: 90 – (Topic 3)

Which three are characteristics of an IPv6 anycast address? (Choose three.)

  1. one-to-many communication model

  2. one-to-nearest communication model

  3. any-to-many communication model

  4. a unique IPv6 address for each device in the group

  5. the same address for multiple devices in the group

  6. delivery of packets to the group interface that is closest to the sending device

Answer: B,E,F

100% Free Download!
Download Free Demo:200-120 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 200-120 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE