[Free] 2017(Oct) Dumps4cert Testinsides Cisco 200-120 Dumps with VCE and PDF Download 31-40

Dumps4Cert 2017 Oct Cisco Official New Released 200-120
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/200-120.html

CCNA Cisco Certified Network Associate CCNA

Question No: 31 – (Topic 2)

Which are valid modes for a switch port used as a VLAN trunk? (Choose three.)

  1. transparent

  2. auto

  3. on

  4. desirable

  5. blocking

  6. forwarding

Answer: B,C,D

Question No: 32 – (Topic 2)

Which statement about VLAN operation on Cisco Catalyst switches is true?

  1. When a packet is received from an 802.1Q trunk, the VLAN ID can be determined from the source MAC address and the MAC address table.

  2. Unknown unicast frames are retransmitted only to the ports that belong to the same VLAN.

  3. Broadcast and multicast frames are retransmitted to ports that are configured on different VLAN.

  4. Ports between switches should be configured in access mode so that VLANs can span across the ports.

Answer: B

Question No: 33 – (Topic 2)

What are the possible trunking modes for a switch port? (Choose three.)

  1. transparent

  2. auto

  3. on

  4. desirable

  5. client

  6. forwarding

Answer: B,C,D

Question No: 34 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

The output that is shown is generated at a switch. Which three statements are true? (Choose three.)

  1. All ports will be in a state of discarding, learning, or forwarding.

  2. Thirty VLANs have been configured on this switch.

  3. The bridge priority is lower than the default value for spanning tree.

  4. All interfaces that are shown are on shared media.

  5. All designated ports are in a forwarding state.

  6. This switch must be the root bridge for all VLANs on this switch.

Answer: A,C,E

Question No: 35 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Switch port FastEthernet 0/24 on ALSwitch1 will be used to create an IEEE 802.1Q- compliant trunk to another switch. Based on the output shown, what is the reason the trunk does not form, even though the proper cabling has been attached?

  1. VLANs have not been created yet.

  2. An IP address must be configured for the port.

  3. The port is currently configured for access mode.

  4. The correct encapsulation type has not been configured.

  5. The “no shutdown” command has not been entered for the port.

Answer: C

Question No: 36 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

A technician has installed SwitchB and needs to configure it for remote access from the management workstation connected to SwitchA. Which set of commands is required to accomplish this task?

  1. SwitchB(config)# interface FastEthernet 0/1 SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown

  2. SwitchB(config)# interface vlan 1

    SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0

    SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0 SwitchB(config-if)# no shutdown

  3. SwitchB(config)# ip default-gateway 192.168.8.254 SwitchB(config)# interface vlan 1

    SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown

  4. SwitchB(config)# ip default-network 192.168.8.254 SwitchB(config)# interface vlan 1

SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown

E. SwitchB(config)# ip route 192.168.8.254 255.255.255.0

SwitchB(config)# interface FastEthernet 0/1

SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0 SwitchB(config-if)# no shutdown

Answer: C

Question No: 37 – (Topic 2)

Which IEEE standard protocol is initiated as a result of successful DTP completion in a switch over Fast Ethernet?

A. 802.3ad B. 802.1w C. 802.1D D. 802.1Q

Answer: D

Question No: 38 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Given the output shown from this Cisco Catalyst 2950, what is the reason that interface FastEthernet 0/10 is not the root port for VLAN 2?

  1. This switch has more than one interface connected to the root network segment in VLAN 2.

  2. This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.

  3. This switch interface has a higher path cost to the root bridge than another in the topology.

  4. This switch has a lower bridge ID for VLAN 2 than the elected designated switch.

Answer: C

Question No: 39 – (Topic 2)

Which two states are the port states when RSTP has converged? (Choose two.)

  1. discarding

  2. listening

  3. learning

  4. forwarding

  5. disabled

Answer: A,D

Question No: 40 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Given this output for SwitchC, what should the network administrator#39;s next action be?

  1. Check the trunk encapsulation mode for SwitchC#39;s fa0/1 port.

  2. Check the duplex mode for SwitchC#39;s fa0/1 port.

  3. Check the duplex mode for SwitchA#39;s fa0/2 port.

  4. Check the trunk encapsulation mode for SwitchA#39;s fa0/2 port.

Answer: C

100% Free Download!
Download Free Demo:200-120 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 200-120 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE