[Free] 2017(Oct) Dumps4cert Testinsides Cisco 200-120 Dumps with VCE and PDF Download 161-170

Dumps4Cert 2017 Oct Cisco Official New Released 200-120
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/200-120.html

CCNA Cisco Certified Network Associate CCNA

Question No: 161 – (Topic 4)

Which command is used to display the collection of OSPF link states?

  1. show ip ospf link-state

  2. show ip ospf lsa database

  3. show ip ospf neighbors

  4. show ip ospf database

Answer: D

Question No: 162 DRAG DROP – (Topic 4)

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Question No: 163 – (Topic 4)

Which three elements must be used when you configure a router interface for VLAN trunking? (Choose three.)

  1. one physical interface for each subinterface

  2. one IP network or subnetwork for each subinterface

  3. a management domain for each subinterface

  4. subinterface encapsulation identifiers that match VLAN tags

  5. one subinterface per VLAN

  6. subinterface numbering that matches VLAN tags

Answer: B,D,E

Question No: 164 – (Topic 4)

A router receives information about network 192.168.10.0/24 from multiple sources. What will the router consider the most reliable information about the path to that network?

  1. a directly connected interface with an address of 192.168.10.254/24

  2. a static route to network 192.168.10.0/24

  3. a RIP update for network 192.168.10.0/24

  4. an OSPF update for network 192.168.0.0/16

  5. a default route with a next hop address of 192.168.10.1

  6. a static route to network 192.168.10.0/24 with a local serial interface configured as the next hop

Answer: A

Question No: 165 – (Topic 4)

A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS image. What function does the router perform next?

  1. It checks the configuration register.

  2. It attempts to boot from a TFTP server.

  3. It loads the first image file in flash memory.

  4. It inspects the configuration file in NVRAM for boot instructions.

Answer: A

Question No: 166 – (Topic 4)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

A network associate has configured OSPF with the command: City(config-router)# network 192.168.12.64 0.0.0.63 area 0

After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.)

  1. FastEthernet0 /0

  2. FastEthernet0 /1

  3. Serial0/0

  4. Serial0/1.102

  5. Serial0/1.103

  6. Serial0/1.104

Answer: B,C,D

Question No: 167 – (Topic 4)

Refer to the graphic.

Dumps4Cert 2017 PDF and VCE

R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)

  1. All of the routers need to be configured for backbone Area 1.

  2. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.

  3. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.

  4. The hello and dead interval timers are not set to the same values on R1 and R3.

  5. EIGRP is also configured on these routers with a lower administrative distance.

  6. R1 and R3 are configured in different areas.

Answer: D,F

Question No: 168 – (Topic 4)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

C-router is to be used as a quot;router-on-a-stickquot; to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

  1. These commands need to be added to the configuration: C-router(config)# router eigrp 123

    C-router(config-router)# network 172.19.0.0

  2. These commands need to be added to the configuration: C-router(config)# router ospf 1

    C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0

  3. These commands need to be added to the configuration: C-router(config)# router rip

    C-router(config-router)# network 172.19.0.0

  4. No further routing configuration is required.

Answer: D

Question No: 169 – (Topic 4)

Which command encrypts all plaintext passwords?

  1. Router# service password-encryption

  2. Router(config)# password-encryption

  3. Router(config)# service password-encryption

  4. Router# password-encryption

Answer: C

Question No: 170 – (Topic 4)

A network administrator is trying to add a new router into an established OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers. Given the information in the partial configuration shown below, what configuration error is causing this problem?

Router(config)# router ospf 1

Router(config-router)# network 10.0.0.0 255.0.0.0 area 0

  1. The process id is configured improperly.

  2. The OSPF area is configured improperly.

  3. The network wildcard mask is configured improperly.

  4. The network number is configured improperly.

  5. The AS is configured improperly.

  6. The network subnet mask is configured improperly.

Answer: C

100% Free Download!
Download Free Demo:200-120 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 200-120 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE