[Free] 2017(Oct) Dumps4cert Testinsides Cisco 100-105 Dumps with VCE and PDF Download 91-100

Dumps4Cert 2017 Oct Cisco Official New Released 100-105
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/100-105.html

Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)

Question No: 91 – (Topic 3)

After the network has converged, what type of messaging, if any, occurs between R3 and R4?

Dumps4Cert 2017 PDF and VCE

  1. No messages are exchanged

  2. Hellos are sent every 10 seconds.

  3. The full database from each router is sent every 30 seconds.

  4. The routing table from each router is sent every 60 seconds.

Answer: B Explanation:

HELLO messages are used to maintain adjacent neighbors so even when the network is converged, hellos are still exchanged. On broadcast and point-to-point links, the default is 10 seconds, on NBMA the default is 30 seconds.

Although OSPF is a link-state protocol the full database from each router is sent every 30 minutes (not seconds) therefore, C and D are not correct.

Question No: 92 – (Topic 3)

Which one of the following IP addresses is the last valid host in the subnet using mask 255.255.255.224?

A. 192.168.2.63

B. 192.168.2.62

C. 192.168.2.61

D. 192.168.2.60

E. 192.168.2.32

Answer: B Explanation:

With the 224 there are 8 networks with increments of 32

One of these is 32 33 62 63 where 63 is broadcast so 62 is last valid host out of given choices.

Question No: 93 – (Topic 3)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which two statements are correct? (Choose two.)

  1. This is a default route.

  2. Adding the subnet mask is optional for the ip route command.

  3. This will allow any host on the 172.16.1.0 network to reach all known destinations beyond RouterA.

  4. This command is incorrect, it needs to specify the interface, such as s0/0/0 rather than an IP address.

  5. The same command needs to be entered on RouterA so that hosts on the 172.16.1.0 network can reach network 10.0.0.0.

Answer: A,C Explanation:

This is obviously the default route which is set between the routers and since it is entered

in such a manner that it ensures connectivity between the stub network and any host lying beyond RouterA.

Question No: 94 – (Topic 3)

What command sequence will configure a router to run OSPF and add network 10.1.1.0

/24 to area 0?

  1. router ospf area 0

    network 10.1.1.0 255.255.255.0 area 0

  2. router ospf

    network 10.1.1.0 0.0.0.255

  3. router ospf 1

    network 10.1.1.0 0.0.0.255 area 0

  4. router ospf area 0

    network 10.1.1.0 0.0.0.255 area 0

  5. router ospf

    network 10.1.1.0 255.255.255.0 area 0

  6. router ospf 1

network 10.1.1.0 0.0.0.255

Answer: C Explanation:

Enabling OSPFSUMMARY STEPS

1.enable 2.configureterminal 3.router ospfprocess-id

4.networkip-addresswildcard-maskareaarea-id 5.end

DETAILED STEPS

Command or Action Purpose

Step 1 enable

Example:

Devicegt; enable

Enables privileged EXEC mode.

->

Step 2

Enter your password if prompted.

configure terminal

Example:

Device# configure terminal Enters global configuration mode.

Step 3

router ospf process-id

Example:

Device(config)# router ospf 109

Enables OSPF routing and enters router configuration mode.

Step 4

network ip-address wildcard-mask area area-id

Example:

Device(config-router)# network 192.168.129.16 0.0.0.3 area 0

Defines an interface on which OSPF runs and defines the area ID for that interface.

Step 5 end

Example:

Device(config-router)# end

Exits router configuration mode and returns to privileged EXEC mode.

Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/configuration/12- 4t/iro-12-4t-book/iro-cfg.html#GUID-588D1301-F63C-4DAC-BF1C-C3735EB13673

Question No: 95 – (Topic 3)

OSPF is configured using default classful addressing. With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF?

Dumps4Cert 2017 PDF and VCE

  1. 2

  2. 3

  3. 4

  4. 5

  5. 6

  6. 7

Answer: C Explanation:

Although OSPF is configured using default classful addressing but OSPF is a link-state routing protocol so it will always send the subnet mask of each network in their advertised routes. Therefore R1 will learn the the complete subnets. Four networks list below will be in the routing table of R1: 172.16.2.64/30 172.16.2.228/30 172.16.2.232/30 172.16.3.0/24

Note: Other networks will be learned as “Directly connected” networks (marked with letter “C”)

Question No: 96 – (Topic 3)

Which two of these functions do routers perform on packets? (Choose two.)

  1. Examine the Layer 2 headers of inbound packets and use that information to determine the next hops for the packets

  2. Update the Layer 2 headers of outbound packets with the MAC addresses of the next

    hops

  3. Examine the Layer 3 headers of inbound packets and use that information to determine the next hops for the packets

  4. Examine the Layer 3 headers of inbound packets and use that information to determine the complete paths along which the packets will be routed to their ultimate destinations

  5. Update the Layer 3 headers of outbound packets so that the packets are properly directed to valid next hops

  6. Update the Layer 3 headers of outbound packets so that the packets are properly directed to their ultimate destinations

Answer: B,C Explanation:

This is the basic function of the router to receive incoming packets and then forward them to their required destination. This is done by reading layer 3 headers of inbound packets and update the info to layer 2 for further hopping.

Question No: 97 – (Topic 3)

Why do large OSPF networks use a hierarchical design? (Choose three.)

  1. to decrease latency by increasing bandwidth

  2. to reduce routing overhead

  3. to speed up convergence

  4. to confine network instability to single areas of the network

  5. to reduce the complexity of router configuration

  6. to lower costs by replacing routers with distribution layer switches

Answer: B,C,D Explanation:

OSPF implements a two-tier hierarchical routing model that uses a core or backbone tier known as area zero (0). Attached to that backbone via area border routers (ABRs) are a number of secondary tier areas.

The hierarchical approach is used to achieve the following:

->Rapid convergence because of link and/or switch failures

->Deterministic traffic recovery

->Scalable and manageable routing hierarchy, reduced routing overhead.

Question No: 98 – (Topic 3)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

If CDP is enabled on all devices and interfaces, which devices will appear in the output of a show cdp neighbors command issued from R2?

  1. R2 and R3

  2. R1 and R3

  3. R3 and S2

  4. R1, S1, S2, and R3

  5. R1, S1, S2, R3, and S3

Answer: C Explanation:

A Cisco device enabled with CDP sends out periodic interface updates to a multicast address in order to make itself known to neighbors. Since it is a layer two protocol, these packets are not routed. So the devices detected would be immediate connected neighbors.

Question No: 99 – (Topic 3)

Which parameter or parameters are used to calculate OSPF cost in Cisco routers?

  1. Bandwidth

  2. Bandwidth and Delay

  3. Bandwidth, Delay, and MTU

  4. Bandwidth, MTU, Reliability, Delay, and Load

Answer: A Explanation:

The well-known formula to calculate OSPF cost is Cost = 108/ Bandwidth

Question No: 100 – (Topic 3)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

Which command would you use to configure a static route on Router1 to network 192.168.202.0/24 with a nondefault administrative distance?

A. router1(config)#ip route 1 192.168.201.1 255.255.255.0 192.168.201.2

B. router1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 1

C. router1(config)#ip route 5 192.168.202.0 255.255.255.0 192.168.201.2

D. router1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 5

Answer: D Explanation:

The default AD for a static route is 1. To change this, configure a different value to be used as the AD at the very end of the “ip route” statement.

100% Free Download!
Download Free Demo:100-105 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 100-105 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE