[Free] 2017(Nov) Dumps4cert Testinsides Cisco 300-208 Dumps with VCE and PDF Download 71-80

Dumps4cert 2017 Nov Cisco Official New Released 300-208
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/300-208.html

Implementing Cisco Secure Access Solutions

Question No: 71

What is the default posture status for non-agent capable devices, such as Linux and iDevices?

  1. Unknown

  2. Validated

  3. Default

  4. Compliant

Answer: D

Question No: 72

What is the first step that occurs when provisioning a wired device in a BYOD scenario?

  1. The smart hub detects that the physically connected endpoint requires configuration and must use MAB to authenticate.

  2. The URL redirects to the Cisco ISE Guest Provisioning portal.

  3. Cisco ISE authenticates the user and deploys the SPW package.

  4. The device user attempts to access a network URL.

Answer: A

Question No: 73

Which configuration must you perform on a switch to deploy Cisco ISE in low-impact mode?

  1. Configure an ingress port ACL on the switchport.

  2. Configure DHCP snooping globally.

  3. Configure IP-device tracking.

  4. Configure BPDU filtering.

Answer: A

Question No: 74

What three changes require restarting the application service on an ISE node? (Choose three.)

  1. Registering a node.

  2. Changing the primary node to standalone.

  3. Promoting the administration node.

  4. Installing the root CA certificate.

  5. Changing the guest portal default port settings.

  6. Adding a network access device.

Answer: A,B,C

Question No: 75

In a basic ACS deployment consisting of two servers, for which three tasks is the primary server responsible? (Choose three.)

  1. configuration

  2. authentication

  3. sensing

  4. policy requirements

  5. monitoring

  6. repudiation

Answer: A,B,D

Question No: 76

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

You are configuring permissions for a new Cisco ISE standard authorization profile. If you configure the Tunnel-Private-Group-ID attribute as shown, what does the value 123 represent?

  1. the VLAN ID

  2. the VRF ID

  3. the tunnel ID

  4. the group ID

Answer: A

Question No: 77

Which default identity source is used by the MyDevices_Portal_Sequence identity source sequence?

  1. internal users

  2. guest users

  3. Active Directory

  4. internal endpoints

  5. RADIUS servers

Answer: A

Question No: 78

Which set of commands allows IPX inbound on all interfaces?

  1. ASA1(config)# access-list IPX-Allow ethertype permit ipxASA1(config)# access-group IPX-Allow in interface global

  2. ASA1(config)# access-list IPX-Allow ethertype permit ipxASA1(config)# access-group IPX-Allow in interface inside

  3. ASA1(config)# access-list IPX-Allow ethertype permit ipxASA1(config)# access-group IPX-Allow in interface outside

  4. ASA1(config)# access-list IPX-Allow ethertype permit ipxASA1(config)# access-group IPX-Allow out interface global

Answer: A

Question No: 79

Which three components comprise the Cisco ISE profiler? (Choose three.)

  1. the sensor, which contains one or more probes

  2. the probe manager

  3. a monitoring tool that connects to the Cisco ISE

  4. the trigger, which activates ACLs

  5. an analyzer, which uses configured policies to evaluate endpoints

  6. a remitter tool, which fails over to redundant profilers

Answer: A,B,E

Question No: 80

When MAB is configured, how often are ports reauthenticated by default?

  1. every 60 seconds

  2. every 90 seconds

  3. every 120 seconds

  4. never

Answer: D

100% Free Download!
Download Free Demo:300-208 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4cert 300-208 Full Exam PDF and VCE

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4cert IT Certification PDF and VCE