[Free] 2017(Nov) Dumps4cert Testinsides Cisco 300-208 Dumps with VCE and PDF Download 21-30

Dumps4cert 2017 Nov Cisco Official New Released 300-208
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/300-208.html

Implementing Cisco Secure Access Solutions

Question No: 21

Which two statements about administrative access to the Cisco Secure ACS SE are true? (Choose two.)

  1. The Cisco Secure ACS SE supports command-line connections through a serial-port connection.

  2. For GUI access, an administrative GUI user must be created by using the add-guiadmin command.

  3. The Cisco Secure ACS SE supports command-line connections through an Ethernet interface.

  4. An ACL-based policy must be configured to allow administrative-user access.

  5. GUI access to the Cisco Secure ASC SE is not supported.

Answer: B,D

Question No: 22

Which two Cisco ISE administration options are available in the Default Posture Status setting? (Choose two.)

  1. Unknown

  2. Compliant

  3. FailOpen

  4. FailClose

  5. Noncompliant

Answer: B,E

Question No: 23

Which profiling capability allows you to gather and forward network packets to an analyzer?

  1. collector

  2. spanner

  3. retriever

  4. aggregator

Answer: A

Question No: 24

Which advanced authentication setting is needed to allow an unknown device to utilize Central WebAuth?

  1. If Authentication failed gt; Continue

  2. If Authentication failed gt; Drop

  3. If user not found gt; Continue

  4. If user not found gt; Reject

Answer: C

Question No: 25

A security engineer has a new TrustSec project and must create a few static security group tag classifications as a proof of concept. Which two classifications can the tags be mapped to? (Choose two.)

  1. VLAN

  2. user ID

  3. interface

  4. switch ID

  5. MAC address

Answer: A,C

Explanation: In static classification the tag maps to some thing (an IP, subnet, VLAN, or interface) rather than relying on an

authorization from the Cisco ISE.

This process of assigning the SGT is defined as “classification.” These classifications are thentransported

deeper into the network for policy enforcement

Question No: 26 CORRECT TEXT

The Secure-X company has started to tested the 802.1X authentication deployment using the Cisco Catalyst 3560-X layer 3 switch and the Cisco ISEvl2 appliance. Each employee desktop will be connected to the 802.1X enabled switch port and will use the Cisco AnyConnect NAM 802.1X supplicant to log in and connect to the network.

Your particular tasks in this simulation are to create a new identity source sequence named AD_internal which will first use the Microsoft Active Directory (AD1) then use the ISE Internal User database. Once the new identity source sequence has been configured, edit the existing DotlX authentication policy to use the new AD_internal identity source sequence.

The Microsoft Active Directory (AD1) identity store has already been successfully configured, you just need to reference it in your configuration.

Dumps4Cert 2017 PDF and VCE

In addition to the above, you are also tasked to edit the IT users authorization policy so IT users who successfully authenticated will get the permission of the existing IT_Corp authorization profile.

Perform this simulation by accessing the ISE GUI to perform the following tasks:

  • Create a new identity source sequence named AD_internal to first use the Microsoft Active Directory (AD1) then use the ISE Internal User database

  • Edit the existing Dot1X authentication policy to use the new AD_internal identity source sequence:

  • If authentication failed-reject the access request

  • If user is not found in AD-Drop the request without sending a response

  • If process failed-Drop the request without sending a response

  • Edit the IT users authorization policy so IT users who successfully authenticated will get the permission of the existing IT_Corp authorization profile.

    To access the ISE GUI, click the ISE icon in the topology diagram. To verify your configurations, from the ISE GUI, you should also see the Authentication Succeeded event for the it1 user after you have successfully defined the DotlX authentication policy to use the Microsoft Active Directory first then use the ISE Internal User Database to authenticate the user. And in the Authentication Succeeded event, you should see the IT_Corp authorization profile being applied to the it1 user. If your configuration is not correct and ISE can#39;t authenticate the user against the Microsoft Active Directory, you should see the Authentication Failed event instead for the it1 user.

    Note: If you make a mistake in the Identity Source Sequence configuration, please delete the Identity Source Sequence then re-add a new one. The edit Identity Source Sequence function is not implemented in this simulation.

    Dumps4Cert 2017 PDF and VCE

    Dumps4Cert 2017 PDF and VCE

    Answer: Review the explanation for full configuration and solution.

    Explanation:

    Step 1: create a new identity source sequence named AD_internal which will first use the Microsoft Active Directory (AD1) then use the ISE Internal User database as shown below:

    Dumps4Cert 2017 PDF and VCE

    Step 2: Edit the existing Dot1x policy to use the newly created Identity Source:

    Dumps4Cert 2017 PDF and VCE

    Then hit Done and save.

    Question No: 27

    A company wants to allow employees to register and manage their own devices that do not support NSP. Which portals enable this?

    1. MDM portals

    2. Client provisioning portals

    3. My devices portals

    4. BYOD Portals

    Answer: C

    Question No: 28

    Which profiling probe collects the user-agent string?

    1. NetFlow

    2. DHCP

    3. Network Scan

    4. HTTP

    Answer: D

    Question No: 29

    Which two component are required for creating native supplicant profile ?

    1. Operative System

    2. Connection type wired/wireless

    3. Ios Sutten

    4. BYOD

    Answer: A,B

    Question No: 30

    During client provisioning on a Mac OS X system, the client system fails to renew its IP address. Which change can you make to the agent profile to correct the problem?

    1. Enable the Agent IP Refresh feature.

    2. Enable the Enable VLAN Detect Without UI feature.

    3. Enable CRL checking.

    4. Edit the Discovery Host parameter to use an IP address instead of an FQDN.

    Answer: A

    100% Free Download!
    Download Free Demo:300-208 Demo PDF
    100% Pass Guaranteed!
    Download 2017 Dumps4cert 300-208 Full Exam PDF and VCE

    Dumps4cert ExamCollection Testking
    Lowest Price Guarantee Yes No No
    Up-to-Dated Yes No No
    Real Questions Yes No No
    Explanation Yes No No
    PDF VCE Yes No No
    Free VCE Simulator Yes No No
    Instant Download Yes No No

    2017 Dumps4cert IT Certification PDF and VCE