[Free] 2017(Nov) Dumps4cert Testinsides Cisco 300-180 Dumps with VCE and PDF Download 171-180

Dumps4cert 2017 Nov Cisco Official New Released 300-180
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/300-180.html

Troubleshooting Cisco Data Center Infrastructure

Question No: 171 – (Topic 2)

Which statement is true regarding Cisco FabricPath?

  1. It is necessary to first install the Cisco FabricPath feature set in the default VDC.

  2. Cisco FabricPath is only available on Cisco Nexus 7010 Switches with the Supervisor 2 engine.

  3. Cisco FabricPath cannot be disabled explicitly for a specific VDC.

  4. If the Cisco FabricPath feature is not installed, the fabricpath keyword will be available in the feature-set command.

Answer: A

Question No: 172 – (Topic 2)

Which two occurrences happen during an ISSU? (Choose two.)

  1. FLOGI/fdisc or logo requests from servers fail until the ISSU is complete.

  2. The time-to-live value for CDP is increased (360 seconds) if it is less than the recommended timeout value.

  3. LACP is not affected because ISSU should not impact peers that rely on LACP because the recovery time is less than 90 seconds.

  4. NTP sessions stay alive and active.

  5. The control plane is offline for up to 300 seconds.

Answer: A,C

Question No: 173 – (Topic 2)

Which statement is true regarding STP?

  1. When the spanning-tree topology is calculated based on default parameters, the path between the source and destination end stations in a switched network might not be ideal.

  2. The path between the source and the destination end stations is always ideal with the default spanning-tree parameter.

  3. The path between the source and the destination end stations is determined by the speed of the link; the slowest link speed will become the root port during the election.

  4. The path between the source and the destination end stations is determined by the lowest MAC address; the lowest MAC address will become the root port during the election.

Answer: A

Question No: 174 – (Topic 2)

You are no longer seeing updates to the device-aliases database on your Cisco Nexus 5596UP Switch. Which command is useful to determine if the scope of Cisco Fabric Services application distribution was being administratively limited?

  1. N5K2# show cfs region

  2. N5K2# show cfs scope

  3. N5K2# show cfs locale

  4. N5K2# show cfs acl

  5. N5K2# show cfs firewall

Answer: A

Question No: 175 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

You configure a vPC between two Cisco Nexus 7010 Switches. The peer link will not come up.

What is the problem?

  1. The vPC domain numbers must be different.

  2. The role priority must be the same.

  3. The system priority must be the same.

  4. The configuration is incorrect.

Answer: C

Question No: 176 – (Topic 2)

FCoE appears to be properly configured. Which two steps should you take to verify the FCoE configuration? (Choose two.)

  1. Run the feature fcoe command.

  2. Verify that the jumbo MTU is properly set.

  3. Ensure that the license has been applied.

  4. Utilize the proper CoS values on each side.

Answer: B,D

Question No: 177 – (Topic 2)

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

FCoE traffic from C200-1 on VSAN 13 is not being switched through the network. Which statement explains the cause of the problem?

  1. The LAN switchport on N5K2 must be configured as a trunk.

  2. VLAN 1013 on N5K2 is not allowed on the LAN.

  3. The vFC on N5K2 that is associated with VSAN 13 is in the wrong port mode.

  4. The M1 card on the Nexus 7000 switch does not support FCoE.

Answer: D

Question No: 178 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

The customer informs you of a problem they are encountering. What is the cause of the problem?

  1. The core upstream switch does not have NPIV enabled.

  2. The downstream switch does not have NPIV enabled.

  3. NPIV has been disabled on all switches.

  4. NPIV has been configured but not enabled on the uplink port.

Answer: A

Question No: 179 – (Topic 2)

Which option describes why the merge status for any application shows quot;In Progressquot; for a prolonged period of time when a new switch is added to the fabric?

  1. The new switch must be upgraded to match the same version of code as the original switch.

  2. The ports between the switches are not trunking all VSANs.

  3. The application needs to be started on both switches.

  4. There are outstanding changes that must be committed.

  5. The merge status cannot occur until a copy running-config startup-config is done.

Answer: D

Question No: 180 – (Topic 2)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

VSAN traffic is not being routed through SAN fabric. Which action is helpful to resolve the problem?

  1. Make sure that the FSPF hello interval value matches on both switches.

  2. Change the FSPF hello timer back to the default of 5 seconds.

  3. Make sure that the FSPF hello timers are different so that they do not compete.

  4. Make sure that the FSPF dead timers are both set to 0.

Answer: A

100% Free Download!
Download Free Demo:300-180 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4cert 300-180 Full Exam PDF and VCE

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4cert IT Certification PDF and VCE