[Free] 2017(Nov) Dumps4cert Testinsides Cisco 300-180 Dumps with VCE and PDF Download 141-150

Dumps4cert 2017 Nov Cisco Official New Released 300-180
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/300-180.html

Troubleshooting Cisco Data Center Infrastructure

Question No: 141 – (Topic 1)

A customer is configuring SAN pin groups in a Cisco UCS domain. The customer notices that pinning is not working and traffic from the vHBA is not passing over the Fibre Channel uplink port. Which of these must be done for pinning to work correctly?

  1. Include the SAN pin group in a vHBA policy and then include the vHBA policy in the service profile that is assigned to that server.

  2. Include the SAN policy in the Cisco UCS Manager to match with pin groups on the fabric interconnect.

  3. The customer must have Cisco UCS Manager version 2.0 or above.

  4. Fibre Channel switch mode needs to be configured first.

Answer: A

Question No: 142 – (Topic 1)

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Dumps4Cert 2017 PDF and VCE

Which two virtual Fibre Channel interfaces are able to pass trafficVSAN 11? {Choose two.)

  1. 11

  2. 12

  3. 13

  4. 14

  5. 15

  6. 10

Answer: A,B

Question No: 143 – (Topic 1)

What is the maximum number of boot targets for an FCoE vHBA on a Cisco UCS C-Series server?

  1. 1

  2. 2

  3. 3

  4. 4

Answer: D

Question No: 144 – (Topic 1)

Refer to the exhibit. A system administrator reviews the VIF paths and discovers an error. What is the cause of the error?

Dumps4Cert 2017 PDF and VCE

  1. The server has no connection to the SAN.

  2. The server is still booting over SAN.

  3. The server is still booting over iSCSI.

  4. The server has the VIC with errors and needed to make an RMA.

  5. The switch that is connected the fabric interconnect has a port that is unavailable.

Answer: C

Question No: 145 – (Topic 1)

You have a Cisco UCS cluster and you must recover a lost admin password. In which order must you power cycle the fabric interconnects?

  1. primary first, and then secondary

  2. secondary first, and then primary

  3. primary and secondary simultaneously

  4. primary only

Answer: B

Question No: 146 – (Topic 1)

A customer is trying to boot an operating system installed on a Cisco UCS B-Series blade server after a RAID1 cluster migration. The RAID LUN remains in inactive state during and

after the service profile association and the server does not boot. What is the cause of this problem?

  1. RAID1 is not supported in cluster migration mode on a Cisco UCS B-Series blade server.

  2. The local disk configuration policy in the service profile on the server is configured with Any Configuration mode rather than RAID1.

  3. The server needs to be booted via SAN in cluster migration to support RAID1.

  4. The Cisco UCS B-Series blade server has older firmware that needs to be updated first.

Answer: B

Question No: 147 – (Topic 1)

You use dynamic vNICs. You create a new service profile. You receive an error message that indicates that you exceeded the number of dynamic vNICs. Which two components can affect the maximum number of dynamic vNICs in the Cisco UCS environment? (Choose two.)

  1. the model of the fabric interconnects

  2. the number of chassis uplinks

  3. the model of the FEX

  4. VMDirectPath sizing

Answer: A,B

Question No: 148 – (Topic 1)

Which two areas should you investigate when experiencing problems with the UCS Manager KVM? (Choose two.)

  1. Java complications

  2. network complications

  3. server CPU type

  4. Fabric Interconnects hardware

  5. SSD complications

Answer: A,B

Question No: 149 – (Topic 1)

A customer calls in a trouble ticket complaining of unacceptable read I/O latency on a Cisco UCS C210 M2 server with an LSI MegaRAID 9260-8i with an 8-disk RAID-10 virtual disk. As you validate the RAID controller configuration, which of these configured items impacts read performance at the controller level?

  1. all disks are 146GB 6 Gb SAS 15K RPM SFF

  2. read ahead cache is enabled

  3. BGI rate = 0

  4. strip size = 256k

  5. no hot spare

Answer: D

Question No: 150 – (Topic 1)

A customer is configuring LAN pin groups in a Cisco UCS domain. The customer has two fabric interconnects and would like to associate the pin group with only one interconnect. Which statement about this configuration is true?

  1. In a system with two fabric interconnects, you can associate the pin group with only one fabric interconnect, and the other fabric interconnect will not be usable.

  2. In a system with two fabric interconnects, you can only associate the pin group with both fabric interconnects; you cannot associate the pin group with only one fabric interconnect.

  3. In a system with two fabric interconnects, you can associate the pin group with only one fabric interconnect or with both fabric interconnect. This is a supported configuration.

  4. This configuration is not supported in a Cisco UCS domain.

Answer: C

100% Free Download!
Download Free Demo:300-180 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4cert 300-180 Full Exam PDF and VCE

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4cert IT Certification PDF and VCE