[Free] 2017(Nov) Dumps4cert Testinsides Cisco 300-180 Dumps with VCE and PDF Download 101-110

Dumps4cert 2017 Nov Cisco Official New Released 300-180
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4cert.com/300-180.html

Troubleshooting Cisco Data Center Infrastructure

Question No: 101 – (Topic 1)

On a Cisco UCS B-Series data center environment; how many default roles are there when utilizing RBAC for security restriction?

  1. 1

  2. 5

  3. 10

  4. 15

  5. 20

Answer: C

Question No: 102 – (Topic 1)

Which two statements about the Cisco UCS FSM are true? (Choose two.)

  1. The FSM is run on the DME.

  2. The FSM is a workflow model with a finite number of stages.

  3. The FSM is a process to upgrade the firmware.

  4. Cisco UCS has two FSMs.

  5. The FSM is used to observe the physical, logical, and virtual components on the Cisco UCS.

Answer: A,B

Question No: 103 – (Topic 1)

Looking at the Equipment gt; Chassis gt; Servers gt; Server X view from the Cisco UCS Manager GUI, which tab would you select to identify the fabric interconnect uplink associated with a given virtual circuit?

  1. Paths

  2. vNIC Paths

  3. Virtual Circuit Paths

  4. VIF Paths

Answer: D

Question No: 104 – (Topic 1)

While attempting to boot a Cisco UCS server from SAN, you are unable to see the LUN. Which of these are causing the problem? (Choose three.)

  1. VHBA template

  2. RAID policy

  3. zoning

  4. LUN ID

  5. vACLs

  6. disjoint fabrics

Answer: A,C,D

Question No: 105 – (Topic 1)

Refer to the exhibit. A server has a service profile that is configured to boot over iSCSI. During boot, this message is displayed. What is the cause of this message?

Dumps4Cert 2017 PDF and VCE

  1. The local disk is not present.

  2. RAID 0 is not configured on the local disk.

  3. The remote disk is powered off.

  4. The server has not configured the pWWN properly in the boot policy.

Answer: C

Question No: 106 – (Topic 1)

You have remote CLI access using SSH to the Cisco UCS equipement of a customer. Which command must you use to check for system errors in the UCS domain?

  1. show fault

  2. show cluster

  3. show chassis

  4. show failover

Answer: A

Question No: 107 – (Topic 1)

A customer is configuring an upstream disjoint Layer 2 network in a Cisco UCS domain. So far they have configured the following:

Fabric Interconnects are in switching mode.

There is symmetrical configuration for high availability. There are no overlapping VLANs.

Each vNIC is communicating with one disjoint Layer 2 network.

After validating the above, the customer is still having issues with network connectivity. What is the issue?

  1. Overlapping VLANs are allowed in a disjoint Layer 2 network.

  2. The vNIC configuration is incorrect and must communicate with two or more disjoint layer 2 networks.

  3. The fabric interconnect must be in end-host mode for a disjoint Layer 2 network.

  4. Asymmetrical configuration for high availability needs to be configured.

Answer: C

Question No: 108 – (Topic 1)

Refer to the exhibit. Which three statements are true based on the output of quot;show service- profile circuit server 1/3quot;. (Choose three.)

Dumps4Cert 2017 PDF and VCE

  1. vnic eth0 is pinned to module 0 interface 1.

  2. vnic eth1 is pinned to module 1 interface 6.

  3. vnic eth0 is pinned to port channel 1.

  4. vnic eth1 is pinned to port channel 6.

  5. A LAN pin group is configured on vnic eth0.

  6. A LAN pin group is configured on vnic eth1.

Answer: B,C,F

Question No: 109 – (Topic 1)

A customer would like to create an Ethernet traffic monitoring session on a Cisco UCS server to troubleshoot network connectivity. The customer has entered the following commands via CLI:

UCS-A# scope eth-traffic-mon

UCS-A /eth-traffic-mon # scope fabric a

UCS-A /eth-traffic-mon/fabric # create eth-mon-session EthMonitor33

UCS-A /eth-traffic-mon/fabric/eth-mon-session* # create dest-interface 2 12

UCS-A /eth-traffic-mon/fabric/eth-mon-session/dest-interface* # set speed 20gbps UCS-A /eth-traffic-mon/fabric/eth-mon-session/dest-interface* # commit-buffer UCS-A /eth-traffic-mon/fabric/eth-mon-session/dest-interface #

Which outcome will this command sequence produce?

  1. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination port at slot 2, port 12, will set the admin speed to 20 Gb/s, and will commit the transaction.

  2. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination port at slot 2, port 33, will set the admin speed to 20 Gb/s, and will commit the transaction.

  3. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination port at slot 33, port 12, will set the admin speed to 20 Gb/s, and will commit the transaction.

  4. It will create an Ethernet traffic monitoring session to copy and forward traffic to the destination port at slot 2, port 12, will set the admin speed to 10 Gb/s, and will commit the transaction.

Answer: A

Question No: 110 – (Topic 1)

What is the correct sequence to export tech support data from the Cisco IMC GUI interface?

  1. Admin tab gt; Utilities gt; Export Technical Support to TFTP

  2. Utilities tab gt; Utilities gt; Export Technical Support to TFTP

  3. Server tab gt; Utilities gt; Export Technical Support to TFTP

  4. Communications tab gt; Utilities gt; Export Technical Support to TFTP

  5. Support tab gt; Utilities gt; Export Technical Support to TFTP

  6. Help tab gt; Utilities gt; Export Technical Support to TFTP

Answer: A

100% Free Download!
Download Free Demo:300-180 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4cert 300-180 Full Exam PDF and VCE

Dumps4cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4cert IT Certification PDF and VCE