[Free] 2017(Nov) Dumps4cert Testinsides Cisco 300-101 Dumps with VCE and PDF Download 151-160

Dumps4Cert 2017 Nov Cisco Official New Released 300-101
100% Free Download! 100% Pass Guaranteed!
http://www.Dumps4Cert.com/300-101.html

Implementing Cisco IP Routing

Question No: 151 – (Topic 7)

When unicast reverse path forwarding is configured on an interface, which action does the interface take first when it receives a packet?

  1. it verifies that the source has a valid VEF adjacency.

  2. It checks the egress access lists.

  3. it verifies a reverse path via the FIB to the source.

  4. It checks the ingress access lists.

Answer: A

Question No: 152 – (Topic 7)

Which mode of uRPF causes a router interface to accept a packet, if the network to which the packet’s source IP address belongs is found in the router’s FIB?

  1. Strict mode

  2. Loose mode

  3. Auto mode

  4. Desirable mode

Answer: B Explanation:

EXPLANATION/REFRENCE

A number of common types of DoS attacks take advantage of forged or rapidly changing source IP addresses, allowing attackers to thwart efforts by ISPs to locate or filter these attacks. Unicast RPF was originally created to help mitigate such attacks by providing an automated, scalable mechanism to implement the Internet Engineering Task Force (IETF) Best Common Practices 38/Request for Comments 2827 (BCP 38/RFC 2827) anti-spoofing filtering on the customer-to-ISP network edge. By taking advantage of the information stored in the Forwarding Information Base (FIB) that is created by the CEF switching process, Unicast RPF can determine whether IP packets are spoofed or malformed by matching the IP source address

and ingress interface against the FIB entry that reaches back to this source (a so-called reverse lookup). Packets that are received from one of the best reverse path routes back out of the same interface are forwarded as normal. If there is no reverse path route on the sam e interface from which the packet was received, it might mean that the source address was modified, and the packet is dropped (by default).

http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_data_urpf/configuration/xe-3s/sec- data-urpf-xe-3s-book/sec-unicast-rpf-loose- mode.html?referring_site=REamp;pos=1amp;page=http://www.cisco.com/c/en/us/td/docs/ios/12_0 s/feature/guide/srpf_gsr.html#GUID-FFFA94D5- EEFB-4215-9EE1-DB37CD01C2CA

Question No: 153 – (Topic 7)

Which type of address does OSPFv3 use to form neighbor adjacencies and to send LSAs?

  1. unicast IPv6 addresses

  2. link-local addresses

  3. multicast address FF02::5

  4. unicast IPv4 addresses

Answer: C

Question No: 154 – (Topic 7)

Refer to the exhibit.

Dumps4Cert 2017 PDF and VCE

How would you confirm on R1 that load balancing is actually occurring on the default- network (0.0.0.0)?

  1. Use ping and the show ip route command to confirm the timers for each default network resets to 0.

  2. Load balancing does not occur over default networks; the second route will only be used for failover.

  3. Use an extended ping along with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.

  4. Use the traceroute command to an address that is not explicitly in the routing table.

Answer: D Explanation: Explanation

The most simple method to test load balancing is to use the “traceroute” command. If load balancing is working correctly, we will see different paths to reach the destination each time we use that command.

Unknown address will be routed via the default-network 0.0.0.0 so we must use an address that is not explicitly in the routing table.

Question No: 155 – (Topic 7)

If the total bandwidth is 64 kbps and the RTT is 3 seconds, what is the bandwidth delay product?

  1. 8,000 bytes

  2. 16,000 bytes

  3. 24,000 bytes

  4. 32,000 bytes

  5. 62,000 bytes

Answer: C

Question No: 156 – (Topic 7)

Which alerts will be seen on the console when running the command: logging console warnings.?

  1. warnings only

  2. warnings, notifications, error, debugging, informational

  3. warnings, errors, critical, alerts, emergencies

  4. notifications, warnings, errors

  5. warnings, errors, critical, alerts

Answer: C

Question No: 157 – (Topic 7)

Which IP SLA operation can be used to measure round-trip delay for the full path and hop- by-hop round-trip delay on the network?

  1. HTTP

  2. ICMP path echo

  3. TCP connect

  4. ICMP echo

Answer: B

Question No: 158 DRAG DROP – (Topic 7)

Drag each statement about authentication, authorization, and accounting on the left to the matching category on right.

Dumps4Cert 2017 PDF and VCE

Answer:

Dumps4Cert 2017 PDF and VCE

Explanation:

Dumps4Cert 2017 PDF and VCE

2017-05-07_172154

Question No: 159 – (Topic 7)

What are three IPv6 transition mechanisms? (Choose three)

  1. 6to4 tunneling

  2. VPN tunneling

  3. GRE tunneling

  4. ISATAP tunneling

  5. PPP tunneling

  6. Teredo tunneling

Answer: A,D,F Explanation:

Below is a summary of IPv6 transition technologies:

6 to 4 tunneling: This mechanism allows IPv6 sites to communicate with each other over the IPv4 network without explicit tunnel setup. The main advantage of this technology is that it requires no end-node reconfiguration and minimal router configuration but it is not intended as a permanent solution.

ISATAP tunneling (Intra-Site Automatic Tunnel Addressing Protocol): is a mechanism for transmitting IPv6 packets over IPv4 network. The word “automatic” means that once an ISATAP server/router has been set up, only the clients must be configured to connect to it. Teredo tunneling: This mechanism tunnels IPv6 datagrams within IPv4 UDP datagrams, allowing private IPv4 address and IPv4 NAT traversal to be used.

In fact, GRE tunneling is also a IPv6 transition mechanism but is not mentioned in BSCI so we shouldn’t choose it (there are 4 types of IPv6 transition mechanisms mentioned in BSCI; they are manual, 6-to-4, Teredo and ISATAP).

Question No: 160 – (Topic 7)

Which PPP authentication method sends authentication information in cleartext?

  1. MS CHAP

  2. CDPCP

  3. CHAP

  4. PAP

Answer: D

100% Free Download!
Download Free Demo:300-101 Demo PDF
100% Pass Guaranteed!
Download 2017 Dumps4Cert 300-101 Full Exam PDF and VCE

Dumps4Cert ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No

2017 Dumps4Cert IT Certification PDF and VCE